As semiconductor process nodes advance below 5 nm and into the angstrom era, the materials stack beneath the photoresist has become as consequential as the resist itself. Silicon-based anti-reflective coatings and underlayers, collectively referred to as SiARC and silicon underlayer materials, sit at the intersection of optical engineering, etch chemistry, and pattern fidelity. Their role in controlling reflectivity, enabling pattern transfer, and supporting critical dimension uniformity makes them foundational to any advanced node lithography process. Understanding how these materials function, and what drives their selection, is essential for process integration engineers working at the leading edge.
This article examines the technical role of SiARC and spin-on silicon underlayer materials across advanced node patterning schemes, from EUV single exposure to multi-patterning sequences, and outlines the performance parameters and integration considerations that govern material selection in high-volume manufacturing.
What Makes Underlayer Materials Critical for Advanced Node Patterning
In any lithographic process, the underlayer stack serves multiple simultaneous functions. Its primary optical role is to suppress back-reflected light from reaching the photoresist during exposure, preventing standing wave formation and the resulting line-edge roughness that degrades critical dimension control. Silicon-based anti-reflective coatings achieve this through precise tuning of refractive index (n) and extinction coefficient (k) at the exposure wavelength, whether that is 193 nm immersion or EUV at 13.5 nm. The optical constants must be matched to the resist above and the substrate below, making the underlayer an active participant in the optical system rather than a passive layer.
Beyond optical performance, the underlayer must serve as an etch barrier and pattern-transfer layer. In advanced node processes, photoresist films are extremely thin, often below 30 nm for EUV, and cannot withstand the etch cycles needed to pattern the underlying dielectric or metal layers. The silicon underlayer acts as the hard mask intermediate, accepting the pattern from the resist and transferring it with high fidelity into the substrate. This dual optical and mechanical role means that underlayer materials must be engineered across multiple dimensions simultaneously, a complexity that grows sharply as device geometries shrink.
How EUV and Multi-Patterning Reshape Underlayer Requirements
The transition to EUV lithography fundamentally changes the optical environment in which underlayers must operate. At 13.5 nm, nearly all materials absorb strongly, and the optical contrast mechanisms differ substantially from 193 nm immersion. EUV underlayers must be designed with optical constants appropriate for this wavelength regime while also supporting the thin-film resist stacks that EUV processes demand. The requirement for low outgassing under EUV exposure adds another constraint, since volatile species released from underlayer materials can contaminate the reflective optics in EUV scanners, a failure mode with significant tool availability consequences.
Multi-patterning schemes, including self-aligned double patterning (SADP), self-aligned quadruple patterning (SAQP), and litho-etch-litho-etch (LELE) sequences, place additional demands on underlayer materials. Each patterning cycle introduces new etch and deposition steps, and the underlayer must maintain dimensional stability and etch selectivity across multiple process exposures. Planarisation performance becomes critical in multi-patterning contexts: topography from prior layers must be absorbed by the underlayer stack to present a flat surface for subsequent lithography steps. Poor planarisation propagates pattern placement errors across patterning iterations, compounding overlay and CD uniformity challenges that are already tight at advanced nodes.
Underlayer Interactions with High-NA EUV
High-NA EUV systems, which entered development qualification in 2025 and 2026, introduce anamorphic optics and a reduced depth of focus that tightens underlayer thickness control requirements further. Thinner resist films under high-NA EUV increase the relative contribution of the underlayer to overall etch budget, making etch selectivity between the underlayer and the resist above, and between the underlayer and the substrate below, a primary design parameter. Materials development for high-NA EUV underlayers is an active area, with process integration requirements still being defined as scanner availability increases.
Key Performance Parameters in SiARC and Silicon Underlayer Selection
Selecting a SiARC or silicon underlayer for a given process node involves evaluating a set of interdependent performance parameters. Optical constants at the exposure wavelength are the starting point, but the practical requirements extend well beyond n and k values. Thickness uniformity across the wafer must be controlled to within a few angstroms to maintain consistent reflectivity suppression, placing demands on both the material’s spin-coating rheology and the process conditions under which it is applied and cured.
Etch Selectivity and Pattern Transfer Fidelity
Etch selectivity, the ratio of etch rates between the underlayer and adjacent layers, determines how cleanly the pattern transfers from resist through the underlayer into the target film. Silicon-rich underlayers generally offer higher etch selectivity relative to organic carbon-based materials, which is one reason they are favoured in aggressive etch environments at advanced nodes. The silicon content and network structure of the material govern not only etch rate but also the profile of etched features: vertical sidewalls with minimal footing or undercutting are essential for maintaining the intended critical dimension through the full stack.
Thermal Stability and Cure Behaviour
Thermal stability during cure and subsequent process steps is another critical parameter. Silicon underlayers are typically cured at elevated temperatures to drive cross-linking and remove residual solvent. The cure window must be compatible with the thermal budget of the device layer below, and the cured film must remain stable through the thermal excursions of subsequent deposition, etch, and clean steps. Shrinkage during cure affects film thickness and stress, both of which influence overlay accuracy when the underlayer is part of a multi-patterning sequence.
Defect Performance and Purity
Defect density in the applied underlayer film is a yield-critical parameter in high-volume manufacturing. Particles, pinholes, and coating defects in the underlayer propagate directly into patterned features. Ultra-high-purity material formulation, including low levels of metallic impurities and tightly controlled particle counts, is therefore a manufacturing requirement, not merely a quality preference. This is an area where the synthesis route and production environment for the underlayer material have direct consequences for fab yield.
Process Integration Considerations Across Device Types
The specific integration requirements for SiARC and silicon underlayer materials vary considerably across device types, even when the lithography node is nominally the same. Logic devices, DRAM, and NAND flash each present distinct underlayer challenges driven by differences in topography, etch chemistry, and pattern density. In logic front-end-of-line (FEOL) patterning, the underlayer stack must accommodate gate and fin patterning with extremely tight CD uniformity requirements and high pattern placement accuracy. In DRAM, the underlayer interacts with high-aspect-ratio capacitor etch processes that demand exceptional etch selectivity and mechanical robustness.
NAND flash presents perhaps the most demanding planarisation challenge, as the underlayer must absorb the significant topography generated by staircase structures and wordline patterning in three-dimensional memory arrays. MEMS and CMOS image sensor processes introduce additional substrate and thermal constraints that influence underlayer material selection. The implication for process integration engineers is that underlayer materials cannot be selected from a single universal specification; they must be evaluated and qualified against the specific process environment of each device type and patterning module.
PiBond’s lithography and patterning materials are used across this range of device types, including CPUs, GPUs, NAND, and DRAM at leading foundries and memory manufacturers, reflecting the breadth of integration environments that silicon underlayer materials must address in practice.
A Materials-First Approach to Underlayer Development
Effective underlayer development begins at the molecular level. The optical, mechanical, and chemical properties of a SiARC or silicon underlayer are determined by the siloxane resin architecture, the monomer composition, and the formulation strategy, not simply by the spin-coat and cure conditions at the fab. This means that meaningful performance differentiation requires control over the full synthesis chain, from monomer design through polymerisation, formulation, and final quality verification. Fabs that work with suppliers capable of modifying chemistry at the monomer level have access to a broader optimisation space than those limited to formulation-level adjustments of commercially available resins.
The independence of the materials supplier is also a practical consideration for process integration teams. A qualified, independent second source for silicon underlayer materials provides supply chain resilience, a concern that has become more prominent across the semiconductor industry in recent years. PiBond manufactures SiARC and silicon underlayer materials entirely in-house, from proprietary monomer synthesis through resin production and final formulation, in ultra-pure cleanroom facilities in Espoo, Finland, and at its manufacturing plant in Haining, China. This integrated approach means that material properties can be adjusted at the chemistry level in response to specific process integration requirements, rather than through formulation workarounds alone.
As patterning complexity continues to grow with each process generation, the relationship between the materials supplier and the process integration team becomes increasingly collaborative. Underlayer specifications that were fixed at one node may need to be revisited entirely at the next, as new etch chemistries, resist platforms, and scanner capabilities redefine the integration environment. A materials-first development approach, grounded in deep chemistry capability and supported by cleanroom-qualified production, is well positioned to meet these evolving requirements.
Explore PiBond’s advanced materials and applications or contact PiBond to discuss your material requirements.
Related Articles
- Can cleaning process optimization reduce defect density without changing chemistry?
- Cleaning material qualification steps before high-volume fab integration
- What dielectric material qualification involves at each stage of process readiness
This content was generated with the help of AI and it may contain mistakes